Jeep Check Engine Light

Please wait while the page loads…

Jeep Check Engine Light Flashing

Although there are bountiful potential causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are several classic causes including something as prevailing as a loose gas cap. Added classic reasons for a Check Engine Light are dirty mass airflow sensor, a malfunction with the fuel injection system, faulty emissions control part, damaged oxygen sensor, faulty head gasket, or defective spark plugs to name a few. No matter what is the root cause of the Check Engine Light, we have the Jeep Certified Technicians and the certified service protocol to isolate the root problem and repair it as needed to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Jeep issue was fixed.

Every Jeep was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the vehicle on its severe systems. The sensors are continually detecting conditions while sending data to the computerized control unit. If the computerized control unit detects that the data is out of factory specifications, the Check Engine Light brightens telling you that there is a problem. However, that is the limitation of the Check Engine Light – it won’t tell you what strictly is wrong nor what to do about it. That’s where we come in; Bill Estes Chrysler Jeep Dodge Ram provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Particularly Qualified Service technological.

How much does it cost to get the engine light checked?

The average cost for a check engine light diagnosis & testing is typically between $88 and $111. The colossal news, Bill Estes Chrysler Jeep Dodge Ram offers complimentary multi-point inspections and free diagnostics, in most cases, to help mean the cause of your check engine light. The check engine light warns of issues ranging from a gas cap that’s not accurately tightened to a more contentious failure like a combative catalytic converter or a problem with one of the car’s oxygen sensors, so it colossal to get the contractual code reading and diagnosis.

What could cause the check engine light to come on in a Jeep?

When your check engine light comes on, this could be as straightforward as tightening or replacing your gas cap. Likewise, the check engine light could also be a warning of a immense problem that could cause immense damage to your engine and come with a big repair bill. Depending on your make and model, the check engine light will illuminate or blink. A steady glow commonly means something less immense but a flashing check engine light suggests that your vehicle’s engine is in immense trouble and service is basic quickly. If your check engine light is flashing in your Jeep, we incredibly recommend not to drive the vehicle and schedule Jeep service today. Below is a list of the most prevailing reasons your check engine light can come on:

  • Your mass airflow sensor (known as MAF) needs to be replaced. The mass airflow sensor in your Jeep is what determines how much fuel is needed to run your engine efficiently by measuring the amount of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to cognizant changes, like altitude. If your Jeep is having trouble starting, idling rough or has a rapid change in the position of the throttle pedal, this could be a sign of a destructive mass airflow sensor.
  • New Spark Plugs or Plug Wires are needed for your Jeep. The spark plugs are the part of your engine that ignites the air/fuel mixture in the combustion chamber of your vehicle. This explosion is what moves the pistons and makes the engine run. The spark plug wires bring the spark from the ignition coil to the spark plugs. If your spark plugs or spark plug wires are destructive or classical, you will experience poor performance and reduced power. In some extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, extensive to more lavish repairs.
  • The battery is low or dead. The battery in your Jeep is every crucial. Without a car battery, your car won’t start, light up the road ahead, play the radio or charge your phone. Today’s car batteries last much longer than they did plentiful decades ago, and they don’t truly require maintenance. The price of a new one depends on the type of Jeep you drive, but check our classic service coupons and specials.
  • Your O2 Sensor (Oxygen Sensor) needs to be replaced. The Oxygen sensor, admitted as the O2 sensor, measures the amount of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns faster and your vehicle will be less efficient when it comes to fuel economy. So what happens if I don’t replace your O2 sensor? A faulty sensor can not only affect your miles per gallon, but it can cause damage to your catalytic converter and your Jeep ‘s spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to hint the right mixture of air and fuel that enters the cylinders in your engine. A destructive O2 sensor can also cause a car to fail an emissions test.
  • Your Jeep has a vacuum leak. Every Jeep has a vacuum system that performs a expansive assortment of functions. The vacuum system also helps reduce harmful emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can dehydrated out and crack, especially if they’re exposed to exciting heat or extreme cold.
  • One of the most classic and frequent cause is that your Jeep gas cap is loose, damaged or missing. The gas cap for your Jeep serves multiple purposes. It prevents gas fumes from being released when you aren’t driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a destructive fuel cap? If your gas cap is classical or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump. Luckily, to replace a gas cap isn’t lavish. If your check engine light turns on instantly after you put gas in your Jeep, first thing you should check is to make bold the cap isn’t loose — or that it’s still on your car’s roof or at the fuel pump.
  • Issues with any aftermarket items. An aftermarket alarm, exhaust or further item can wreak havoc on your Jeep if it’s not installed properly. These aftermarket parts and accessories can drain the battery, trigger the check engine light, or even prevent the vehicle from starting. If these issues sound simple, bring your to Jeep and have our team of certified mechanics ensure that your aftermarket items were installed correctly and aren’t causing any issue. Getting accessories, especially aftermarket parts and accessories, or using OEM parts first place might cost a little bit more but could save you money from having to get poor work and damage caused by poor installation work corrected.
  • Your catalytic converter is destructive or going destructive. The catalytic converter is a part of your Jeep ’s exhaust system. The catalytic converter’s function is to turn the carbon monoxide created by the combustion process into carbon dioxide. A damaged catalytic converter is usually caused by neglected maintenance, which is why Bill Estes Chrysler Jeep Dodge Ram offers a complimentary multi-point inspection with every Jeep service. If you have an issue with your catalytic converter and don’t get it serviced, your Jeep will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your car may run at a higher temperature, too, which can cause further problems from overheating.

How many miles can you drive with the check engine light?

Since each check engine code has its own level of severity, it is difficult to predict how many miles you can drive with the warning light on. The safest bet is to decipher the code and then plan your strategy accordingly. It could be anything from a bad sensor to plug wires needing to be replaced. If you check engine light is flashing, we recommend that you pull over and contact Bill Estes Chrysler Jeep Dodge Ram to help mean if your car is safe to drive in or if we recommend a tow truck.

Is it safe to drive your Jeep with the check engine light on?

If the check engine light is blinking, this means that there is a alarming issue and it is recommended to service your Jeep immediately. This question is not very straightforward because it all depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be firm to drive. This is naturally indicated by a persistent glow of the check engine light. If you notice a difference in the performance of the automobile, it could be an indication of a more perilous problem. Call the experts at Bill Estes Chrysler Jeep Dodge Ram by dialing 3178540239 so you can describe the issues. Or reduce your speed and bring your Jeep to our certified mechanics as soon as fair.

What Does the Check Engine Light Mean?

One of the most mostly misunderstood lights or indicators in your Jeep is the check engine light. The check engine light is part of the onboard diagnostics system, and displays in a few different ways. It can say “Check Engine”, it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your vehicle. Onboard computers increasingly have controlled and monitored vehicle performance since the 80s and do a variety of things for your Jeep. Some of these include controlling engine speed, shifting automatic transmissions ignition timing, and implementing stability control, just to name a few. With that being said, the check engine light can recommend a variety of different things. It can be as cordial as your gas cap being loose or as harsh as engine knocking. If your check engine light is on in your Jeep, contact Bill Estes Chrysler Jeep Dodge Ram. Contact Bill Estes Chrysler Jeep Dodge Ram today! Our Jeep service department can help you find out what code is turning your check engine light on or observe why your check engine light is flashing.

Jeep Check Engine Light

A glaring light expresses that the problem is treacherous and if not taken care of immediately may result in considerable damage to the vehicle. If the check engine light in your Jeep starts glaring, that means that the problem needs hasty attention and your Jeep should be transported in immediately. This blinking light regularly indicates a rigorous engine misfire allowing unburned fuel to be dumped into the exhaust system. There it can immediately boost the temperature of the catalytic converter to a point where damage is available, requiring an costly repair. Some owners ask if spark plugs cause the check engine light to flash? This can entirely be the cause. A bad, classical or dirty spark plug can cause the engine to misfire. If the problem is ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a very expensive repair. If your check engine light is shining, please contact our department of automotive advisors at Bill Estes Chrysler Jeep Dodge Ram suddenly by calling 3178540239.

Jeep Check Engine Light Codes

The check engine light turning on can be quite intimidating to see that little light on your vehicle’s dashboard instantly illuminates, but in reality, it is not something that should cause you to shut down in fear right away. If you hear the term, diagnostic trouble codes (DTC), these are just other name for check engine light codes. These are automotive computer codes stored by the ECM, also modern as the OBD (on-board computer diagnostic system) in your. There are hundreds of diverse codes that your check engine light can hint. While that sounds daunting, with a little patience, tackling principal diagnostics will give you classic knowledge about your vehicle and will also allow that Check Engine Light to do what it is genuinely supposed to do: be your guide. Unfortunately, clear and accessible vehicle symptoms do not always accompany an illuminated Check Engine Light. Since there are hundreds of probable OBD codes, there are also hundreds of probable reasons for the light, including:

  • Transmission issues
  • Fuel and air metering systems problems
  • Old Battery
  • Bad Spark Plugs
  • Computer output circuit issues
  • O2 Sensor
  • Ignition system faults
  • Loose Gas Cap or Missing Gas Cap
  • Emissions controls issues

This is why it is noticeable for someone who does not have a few of automotive knowledge to not assume what a code means. When your check engine light comes on, you should get it checked out immediately by a certified Jeep mechanic. Call Bill Estes Chrysler Jeep Dodge Ram at 3178540239 swiftly or schedule your check engine light service online today! If the engine light comes on due to a unsafe concern, you risk damaging your car additional by not repairing the issue right away.

Will the check engine light reset itself?

The check engine light on your Jeep will generally shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it’s tightened, the light will turn itself off. Likewise, if your catalytic converter is going persistent, and you did a few of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your Jeep light will go off after about 20-40 miles. If you drive over that amount and the light is still on, you will need to bring it in to Bill Estes Chrysler Jeep Dodge Ram so the light and code can be double-checked and reset.

Check Engine Light Service Jeep

What do you do when you’re driving along in your Jeep and suddenly, a yellow light flashes on your dash and says “Check Engine”. If you’re like most Jeep owners, your heart sinks a little because you have little idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep breath and realize the light coming on doesn’t imply you have to pull the car over to the side of the road and call a tow truck, but it is recommended that you get your Jeep checked as soon as potential. Ignoring that warning could end up causing broad damage to expensive engine components.

When your Jeep ‘s ECM (electronic control module), which is the vehicle’s onboard computer, finds a problem in the electrical control system that it can’t realistic, a computer turns on your check engine light. This amber or yellow light is constantly labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that identifies as the issue, whether it’s a sensor or a failing engine part. This code is read with an electronic observe tool that is used by our Jeep auto repair mechanics at Bill Estes Chrysler Jeep Dodge Ram. There are also a number of relatively cheap code readers that are designed for do-it-yourselfers, should you select that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an experienced professional to imply the issue and repair it.