2013 Jeep Wrangler Check Engine Light

What could cause the check engine light to come on in a 2013 Jeep Wrangler?

When your check engine light comes on, this could be as common as tightening or replacing your gas cap. Likewise, the check engine light could also be a warning of a alarming problem that could cause alarming damage to your engine and come with a colossal repair bill. Depending on your make and model, the check engine light will illuminate or blink. A steady glow customarily means something less alarming but a flashing check engine light hints that your vehicle’s engine is in alarming trouble and service is decisive abruptly. If your check engine light is flashing in your 2013 Jeep Wrangler, we exceedingly recommend not to drive the vehicle and schedule Jeep service now. Below is a list of the most present reasons your check engine light can come on:

• Your O2 Sensor (Oxygen Sensor) needs to be replaced. The Oxygen sensor, known as the O2 sensor, measures the deposit of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns faster and your car will be fewer essential when it comes to fuel economy. So what happens if I don’t replace your O2 sensor? A faulty sensor can not only affect your miles per gallon, but it can cause break to your catalytic converter and your 2013 Jeep Wrangler's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to learn the prudent mixture of air and fuel that enters the cylinders in your engine. A bad O2 sensor can also cause a car to fail an emissions test.
• The battery is low or dead. The battery in your 2013 Jeep Wrangler is every exciting. Without a car battery, your car won’t start, light up the road ahead, play the radio or charge your phone. Today’s car batteries last much longer than they did some decades ago, and they don't really require maintenance. The rate of a new one depends on the type of Jeep you travel to work, but check our decent service coupons and specials.
• Your 2013 Jeep Wrangler has a vacuum leak. Every Jeep Wrangler has a vacuum system that performs a great variety of functions. The vacuum system also helps lower aggressive emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can arid out and crack, especially if they’re exposed to exciting heat or extreme furious.
• New Spark Plugs or Plug Wires are mandatory for your 2013 Jeep Wrangler. The spark plugs are the part of your engine that ignites the air/fuel mixture in the combustion chamber of your car. This explosion is what moves the pistons and makes the engine run. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If your spark plugs or spark plug wires are bad or old, you will experience scanty performance and reduced power. In some extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or break to ignition coils and O2 sensors, essential to more expensive repairs.
• Your mass airflow sensor (known as MAF) needs to be replaced. The mass airflow sensor in your Jeep Wrangler is what determines how much fuel is mandatory to run your engine efficiently by measuring the deposit of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to actual changes, like altitude. If your Jeep Wrangler is having trouble starting, idling rough or has a sudden change in the position of the throttle pedal, this could be a sign of a bad mass airflow sensor.
• Your catalytic converter is bad or going bad. The catalytic converter is a part of your 2013 Jeep Wrangler’s exhaust system. The catalytic converter's function is to turn the carbon monoxide created by the combustion process into carbon dioxide. A damaged catalytic converter is usually caused by neglected maintenance, which is why Bill Estes Chrysler Jeep Dodge Ram offers a complimentary multi-point inspection with every Jeep service. If you have an issue with your catalytic converter and don't get it repaired, your 2013 Jeep Wrangler will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your car may run at a higher temperature, too, which can cause other problems from overheating.
• Issues with any aftermarket items. An aftermarket alarm, exhaust or other item can wreak havoc on your 2013 Jeep Wrangler if it’s not installed properly. These aftermarket parts and accessories can discard the battery, trigger the check engine light, or even prevent the car from starting. If these issues sound common, bring your Wrangler to Jeep and have our team of certified mechanics ensure that your aftermarket items were installed correctly and aren't causing any issue. Getting accessories, especially aftermarket parts and accessories, or using OEM parts first place might estimate some bit more but could save you money from having to get scanty work and break caused by scanty installation work corrected.
• One of the most decent and countless cause is that your 2013 Jeep Wrangler gas cap is loose, damaged or missing. The gas cap for your 2013 Jeep Wrangler serves multiple purposes. It prevents gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a bad fuel cap? If your gas cap is old or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump. Luckily, to replace a gas cap isn't expensive. If your check engine light turns on urgently after you put gas in your 2013 Jeep Wrangler, first thing you should check is to make sure the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.

2013 Jeep Wrangler Check Engine Light Flashing

Although there are countless potential causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are several accepted causes including something as distinct as a loose gas cap. Other accepted reasons for a Check Engine Light are faulty emissions control part, dirty mass airflow sensor, faulty head gasket, damaged oxygen sensor, a malfunction with the fuel injection system, or defective spark plugs to name assorted. No matter what is the root cause of the Check Engine Light, we have the Jeep Certified Technicians and the certified service protocol to isolate the root problem and repair it as needed to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Jeep issue was revamped.

Every 2013 Jeep Wrangler was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the vehicle on its critical systems. The sensors are constantly detecting conditions while sending data to the electronic control unit. If the electronic control unit detects that the data is out of factory specifications, the Check Engine Light illuminates telling you that there is a problem. However, that is the limitation of the Check Engine Light – it won’t tell you what totally is untrue nor what to do about it. That’s where we come in; Bill Estes Chrysler Jeep Dodge Ram provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Extraordinarily Qualified Service professional.

Will the check engine light reset itself?

The check engine light on your 2013 Jeep Wrangler will typically shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will turn itself off. Likewise, if your catalytic converter is going intelligent, and you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your 2013 Jeep Wrangler light will go off after about 20-40 miles. If you travel to work over that sum and the light is still on, you will need to bring it in to Bill Estes Chrysler Jeep Dodge Ram so the light and code can be double-checked and reset.

How many miles can you drive with the check engine light?

Since each check engine code has its own level of severity, it is difficult to predict how frequent miles you can drive with the warning light on. If you check engine light is flashing, we recommend that you pull over and contact Bill Estes Chrysler Jeep Dodge Ram to help mean if your vehicle is reliable to drive in or if we recommend a tow truck. The safest bet is to decipher the code and then plan your strategy accordingly. It could be anything from a bad sensor to plug wires needing to be replaced.

What Does the Check Engine Light Mean?

One of the most typically misunderstood lights or indicators in your 2013 Jeep Wrangler is the check engine light. The check engine light is part of the onboard diagnostics system, and displays in critical contrasting ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your car. Onboard computers increasingly have controlled and monitored car performance since the 80s and do a variety of things for your 2013 Jeep Wrangler. Some of these include controlling engine speed, shifting automatic transmissions ignition timing, and implementing stability control, just to name a few. With that being said, the check engine light can mean a mixture of assorted things. It can be as simple as your gas cap being loose or as risky as engine knocking. If your check engine light is on in your 2013 Jeep Wrangler, contact Bill Estes Chrysler Jeep Dodge Ram. Our Jeep service department can help you find out what code is turning your check engine light on or diagnose why your check engine light is flashing. Contact Bill Estes Chrysler Jeep Dodge Ram today!

2013 Jeep Wrangler Check Engine Light

A shining light indicates that the problem is precarious and if not taken care of urgently may result in broad damage to the vehicle. If the check engine light in your 2013 Jeep Wrangler starts shining, that means that the problem needs immediate attention and your Jeep should be brought in urgently. This blinking light usually indicates a strict engine misfire allowing unburned fuel to be dumped into the exhaust system. There it can swiftly enhance the temperature of the catalytic converter to a point where damage is likely, requiring an expensive repair. A Little owners ask if spark plugs cause the check engine light to flash? This can absolutely be the cause. A bad, departed or dirty spark plug can cause the engine to misfire. If your check engine light is flashing, please contact our squad of automotive advisors at Bill Estes Chrysler Jeep Dodge Ram quickly by calling 3178540239. If the problem is ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a very expensive repair.

Is it safe to drive your 2013 Jeep Wrangler with the check engine light on?

This question is not very discernible because it all depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be safe to drive. This is frequently indicated by a suitable glow of the check engine light. If you notice a difference in the performance of the vehicle, it could be an indication of a more perilous problem. If the check engine light is flashing, this means that there is a perilous issue and it is recommended to service your Jeep Wrangler quickly. Call the experts at Bill Estes Chrysler Jeep Dodge Ram by dialing 3178540239 so you can describe the issues. Or lower your speed and bring your 2013 Jeep to our certified mechanics as soon as convenient.

How much does it cost to get the engine light checked?

The middle price for a check engine light diagnosis & testing is generally between $88 and $111. The conclusive news, Bill Estes Chrysler Jeep Dodge Ram offers complimentary multi-point inspections and free diagnostics, in most cases, to help indicate the cause of your check engine light. The check engine light warns of issues ranging from a gas cap that's not accurately tightened to a more precarious failure like a bad catalytic converter or a problem with one of the car's oxygen sensors, so it conclusive to get the contractual code reading and diagnosis.

Check Engine Light Service 2013 Jeep Wrangler

What do you do when you’re driving along in your Jeep Wrangler and suddenly, a yellow light brightens on your dash and says "Check Engine". If you’re like most Jeep owners, your heart sinks a scant because you have scant idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep breath and realize the light coming on doesn’t mean you have to pull the car over to the side of the road and call a tow truck, but it is recommended that you get your 2013 Jeep Wrangler checked as soon as attainable. Ignoring that warning could end up causing extensive damage to lavish engine components.

When your 2013 Jeep Wrangler's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t correct, a computer turns on your check engine light. This amber or yellow light is naturally labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that identifies as the issue, whether it's a sensor or a failing engine part. This code is read with an electronic scan tool that is used by our Jeep auto repair mechanics at Bill Estes Chrysler Jeep Dodge Ram. There are also a number of relatively correct code readers that are designed for do-it-yourselfers, should you select that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an experienced high-tech to suggest the issue and repair it.

2013 Jeep Wrangler Check Engine Light Codes

The check engine light turning on can be quite intimidating to see that miniature light on your vehicle’s dashboard hastily illuminates, but in reality, it is not something that should cause you to shut down in fear modest away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, also known as the OBD (on-board computer diagnostic system) in your Wrangler. There are hundreds of understandable codes that your check engine light can indicate. While that sounds daunting, with a miniature patience, tackling crucial diagnostics will give you convenient knowledge about your vehicle and will also allow that Check Engine Light to do what it is certainly supposed to do: be your guide. Unfortunately, convenient and helpful vehicle symptoms do not always accompany an illuminated Check Engine Light. Since there are hundreds of handy OBD codes, there are also hundreds of handy reasons for the light, including:

• Loose Gas Cap or Missing Gas Cap
• O2 Sensor
• Emissions controls issues
• Bad Spark Plugs
• Transmission issues
• Fuel and air metering systems problems
• Old Battery
• Computer output circuit issues
• Ignition system faults

This is why it is basic for someone who does not have numerous of automotive knowledge to not assume what a code means. Call Bill Estes Chrysler Jeep Dodge Ram at 3178540239 today or schedule your check engine light service online today! When your check engine light comes on, you should get it checked out rapidly by a certified Jeep mechanic. If the engine light comes on due to a strict concern, you risk damaging your car further by not repairing the issue honest away.